Skip to content
Pool Base

Start here

Pool water chemistry, explained without the jargon

Six readings decide whether pool water is safe, comfortable and kind to the pool itself. Most charts give one fixed range for each. The trouble is that the right number for one reading depends on the others, and on the pool: its surface, how chlorine gets in, and whether it's indoors.

8 min readUpdated October 22, 2026

Free chlorine: the part that sanitizes

Free chlorine is the chlorine still available to kill germs and break down sweat and sunscreen. It's the most important reading on the strip, and the one that runs out first.

How much you need depends on your stabilizer (cyanuric acid). Stabilizer shields chlorine from sunlight by binding most of it, which also slows it down. The more stabilizer, the more free chlorine it takes to sanitize. A useful rule is to keep free chlorine at least 7.5% of the stabilizer reading, and aim for about 15%. With stabilizer at 40, that's 3 ppm at the very least, 6 ppm as a target. The common '1 to 3 ppm' advice only holds for pools with little or no stabilizer.

Combined chlorine: chlorine that's been used

Total chlorine minus free chlorine is combined chlorine: chlorine that has reacted with ammonia from swimmers and become chloramines. Chloramines cause the 'chlorine smell' and stinging eyes. Above 0.5 ppm the pool needs shocking: raising free chlorine high enough, for long enough, to burn them off.

pH: comfort and chlorine strength

pH runs from acidic (low) to basic (high). Between 7.2 and 7.8 swimmers are comfortable and chlorine does its job. Above 7.8, chlorine loses much of its strength and scale starts to form. Below 7.2, water stings, corrodes metal and etches plaster.

Total alkalinity: what holds pH steady

Alkalinity is the water's buffer: how much acid it takes to move pH. Too low and pH swings with every dose. Too high and pH keeps drifting up, so you add acid every week. Liquid chlorine and salt cells push pH up, so lower alkalinity (60 to 90) works well with them. Chlorine tablets are acidic, so alkalinity is kept higher (80 to 120) to hold pH up.

Calcium hardness: depends on the surface

Plaster, pebble and concrete pools need calcium in the water, or the water dissolves it from the surface. Aim for 250 to 450 ppm. Vinyl and fiberglass pools don't need it, and high calcium only causes scale, so 150 to 350 is plenty. Spas run hot, which makes scale form more easily, so they're kept lower.

Stabilizer (cyanuric acid): sun protection

Outdoors, 30 to 50 ppm of stabilizer keeps sunlight from destroying chlorine in an afternoon. Salt pools run higher (60 to 80) because the cell makes chlorine slowly all day. Indoor pools need little or none. Stabilizer only leaves the water when water does, so it builds up from chlorine tablets over a season and the only fix is draining part of the pool.

Balance: all of them together

pH, alkalinity, calcium and temperature together decide whether water dissolves the pool or coats it in scale. The Langelier Saturation Index (LSI) combines them into one number: between -0.3 and +0.3 is balanced. Fixing pH alone can push balance the wrong way, which is why good dosing looks at every reading at once.

The order you correct things matters too: alkalinity first (it decides how pH responds), then pH, calcium, stabilizer, and chlorine last.

Chart

Target ranges change with the pool. These are the ranges Pool Base's water engine uses for each kind of pool.

PoolFree chlorinepHAlkalinityCalciumStabilizer
Plaster pool, liquid chlorine3–87.2–7.860–100250–45030–50
Vinyl or fiberglass pool3–87.2–7.860–100150–35030–50
Salt pool (plaster)3–77.2–7.860–80250–45060–80
Chlorine tablets (plaster)3–87.2–7.880–120250–45030–50
Indoor pool1–47.2–7.860–100250–4500–20
Spa or hot tub3–6.57.2–7.860–100150–25020–40

Computed by Pool Base's water engine. Confirm a large correction with a drop test before dosing.

Questions

What should my pool chemicals be at?

For a typical outdoor plaster pool on liquid chlorine: pH 7.2 to 7.8, alkalinity 60 to 100, calcium hardness 250 to 450, stabilizer 30 to 50, and free chlorine at least 7.5% of the stabilizer reading (3 ppm at stabilizer 40). Vinyl, salt, indoor pools and spas each differ, as the table shows.

Which pool chemical should I adjust first?

Alkalinity first, because it decides how pH responds. Then pH, then calcium, then stabilizer, and chlorine last. Never add acid and chlorine at the same time or in the same spot.

Why does my pool need so much chlorine?

Usually high stabilizer. Stabilizer binds chlorine, so at stabilizer 80 you need about 6 ppm of free chlorine just to sanitize. If stabilizer is far above 50, partly draining and refilling is the fix.

Let the app work out the doses

Scan the strip, and Pool Base lists what to add, how much, and in what order, for that pool.

No card needed · Month to month · Cancel any time